Old house wiring replacement in Brick
The first step is finding what is actually live. Houses are often partly rewired, and old runs get spliced into new ones. We trace each circuit, disconnect the knob and tube, and run new grounded cable to every device it served. Dead wiring left inside walls is disconnected at both ends.
We also get calls from Brick for knob and tube wiring replacement, knob and tube rewiring and knob and tube removal. If you are not sure which one you need, describe the problem and we will tell you.
What is included
- Tracing of all live knob and tube circuits
- New grounded circuits to replace each run
- Removal of accessible old wiring in basements and attics
- Correction of old-to-new splices
- A letter describing the work for your insurer
- Permit and inspection
Do you need knob and tube wiring replacement? Four signs
- You see ceramic knobs or tubes in the basement or attic
- An insurer or home inspector has flagged it
- You want to insulate the attic or walls
- Outlets are ungrounded and few
Not sure if this is what you need? Call (888) 633-7804, tell us what is happening in your Brick home or business, and we will point you to the right service.
What happens when you call
- We visit the property in Brick, look at the existing equipment and run a load calculation.
- You get a written, itemized price.
- We file for the permit and schedule the utility where the job needs it.
- We do the work in planned stages so you are without power as little as possible.
- The job is inspected, and we walk you through the finished work.
Knob and tube wiring replacement cost in Brick
The cost to replace knob and tube in Brick depends on how much is still live and how easy it is to reach. A house with a few remaining circuits is a very different job from one that was never updated.
Knob and tube wiring replacement near Shore Acres and Osbornville
Whether you are in Herbertsville or out toward Point Pleasant Beach, it is the same crew and the same number: (888) 633-7804. Regular stops include Herbertsville, Lanes Mill, Cedarcroft and Osbornville. We serve ZIP codes 08723 and 08724 and the neighboring towns of Point Pleasant Beach, Brielle, Mantoloking and Manasquan.
Along the Ocean County coast, many homes have been raised, rebuilt or renovated since Sandy, and flood rules affect where panels, meters and outlets can go. We work in the flood zones around Brick regularly and set equipment at the height the town requires.
If you searched for “knob and tube rewiring near Brick”, one more thing worth knowing: we coordinate with PSE&G, JCP&L, Atlantic City Electric, Rockland Electric or a municipal utility when a job needs the power company involved, so you do not have to.
Knob and Tube Wiring Replacement in nearby towns
- Knob and Tube Wiring Replacement in Point Pleasant Beach
- Knob and Tube Wiring Replacement in Brielle
- Knob and Tube Wiring Replacement in Mantoloking
- Knob and Tube Wiring Replacement in Manasquan
- Knob and Tube Wiring Replacement in Allenwood
- Knob and Tube Wiring Replacement in Lakewood
- Knob and Tube Wiring Replacement in Normandy Beach
- Knob and Tube Wiring Replacement in Sea Girt
Knob and tube wiring replacement in Brick: common questions
Is knob and tube wiring illegal?
No, existing installations are allowed to remain. But it cannot be extended, it should not be covered with insulation, and many insurers will not accept it.
Can I insulate over knob and tube?
No. The wiring relies on open air to stay cool. Replace it first, then insulate.
Do you have to open the walls?
Less than you might think. Most new cable is fished from the basement and attic.
Do I need a permit for electrical work in Brick?
New circuits, panel changes and service work generally need a permit from the local construction office. Simple like-for-like replacements usually do not. We tell you when your job needs one.
Do you cover all of Brick?
Yes. We work throughout Brick and Ocean County, including ZIP codes 08723 and 08724, from Herbertsville to Osbornville.